Was your keyboard plugged into the hub when you tried the wifi in the hub? I have a hub that causes problems if both keyboard and wifi adapter are plugged into it together. Moving one or the other and plugging directly into a USB port on the Pi and everything works fine.SN wrote:This last question is key. currently my belkin only works direct of the raspi NOT off my powered usb hub. i'm getting ready to buy another dongle and i dont want this issue
I have my wifi adapter, a Micronet N150 adapter SP907NS, plugged directly into the Pi. It is base on the Realtek RTL8188CUS device. The max current I've seen with this device is about 115mA, slightly over the max 100ma spec for the low power USB port, but the fuses are rated 140mA and so there is a reasonable current to spare. There are a number of different manufacturers using this device in their adapters and I would expect the power consumption of those adapters to be similar. I believe there are a fair number of people using adapters based on the RTL8188CUS with the adapter plugged directly into the Pi. Power consumption is at a max during data transmission. Due to the relatively low transmission data rates from the Pi it is pointless looking at high speed devices, e.g. N300 devices which I expect take a relatively high current. Even a 54Mbps device is never likely to get anywhere near maximum speed but may be of relatively low power. Longer range devices will also take more power due to higher tansmission power rates needed to give the longer range. One difficulty is that power usage never seems to be mentioned in data publicly available. so unless someone has measure actual current usage finding a suitable part is near impossible. I found some info for my part on a data sheet on some obscure Chinese web site after a lengthy search on the internet. This gave a max transmission current of 129mA at 86Mbps, a far higher transmission rate that the Pi is ever likely to achieve.Drogyn wrote:Currently waiting for my pi but looking for peripherals for it and sorry if this has been asked but...
Is there sufficient power from the onboard usb to run a wifi dongle or will it have to be plugged into a powered hub?
Have seen some conflicting information and I'm curious if there is a dongle out there that will run from the pi's usb power as i intend on setting it up to access remotely
I too have the same problem with the N10 on the Pi running Squeezeplug. Powered hub no issue but that is a nuisance and requires two power supplies. I can't run the Pi off the hub even though I have a 2A power supply feeding the hub. Maybe the hub limits the power to the Pi causing the same issue. I can communicate with the Pi and the app works but the sound out is badly distorted. So I can only assume the N10 chews too much power and the audio goes wrong.jbuehl wrote:I was able to get an ASUS USB-N10 adapter to work using Arch Linux which includes the r8712u driver if you upgrade the distro. I used netcfg to configure and bring up the interface. I had a lot of intermittent problems with the adapter plugged directly into the board which went away when I began using a powered USB hub. I don't know how much current the ASUS adapter draws, but it gets awfully hot, so it must be quite a lot. I like the small form factor, but I need to find one that doesn't need the hub.
Hi Dave,redstone wrote:Hey guys,
This is my first post on the forum. I just purchased a R Pi and I am in the process of setting it up. I purchased the Edimax EW-7811Un 150 Mbps Wireless 11n Nano. I dont know if it will work or not but I will post when it comes in. Im pretty excited about the whole process, my purpose is a catalyst to teach my daughter about hardware, OS, and software. Anyway, good to meet you guys, looks like a fun and helpful crowd.
Code: Select all
wlan0 Link encap:Ethernet HWaddr 64:70:02:1d:b3:99 inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6670:2ff:fe1d:b399/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2153173 errors:0 dropped:2155824 overruns:0 frame:0 TX packets:1190480 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3147379621 (2.9 GiB) TX bytes:108047158 (103.0 MiB)
Code: Select all
wlan0 IEEE 802.11bgn ESSID:"<snip>" Nickname:"<WIFI@REALTEK>" Mode:Managed Frequency:2.412 GHz Access Point: C8:3A:35:F8:57:90 Bit Rate:150 Mb/s Sensitivity:0/0 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=94/100 Signal level=67/100 Noise level=0/100 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0