Go to advanced search

by andy33
Thu Oct 01, 2015 9:38 pm
Forum: Raspbian
Topic: mplayer build difference between jessie and wheezy
Replies: 1
Views: 2332

Re: mplayer build difference between jessie and wheezy

That is my post that you refer to there. I'm using Mike Bradys shairport-sync utility which I build from source. It works fine in wheezy but when I tried jessie it builds ok and reports no errors and seems to run absolutely fine. The trouble is that no sound is output. I suspect the trouble in my ca...
by andy33
Thu Oct 01, 2015 7:50 pm
Forum: Raspbian
Topic: Jessie: mplayer now not working
Replies: 2
Views: 4961

Jessie: mplayer now not working

I have just tried using mplayer with Jessie using an iqaudio dac, but it returns with this error. mplayer -ao alsa:device=hw=0,0 http://www.radiofeeds.co.uk/bbcradio2.pls MPlayer2 2.0-728-g2c378c7-4+b1 (C) 2000-2012 MPlayer Team Cannot open file '/home/pi/.mplayer/input.conf': No such file or direct...
by andy33
Sun Sep 20, 2015 9:15 pm
Forum: Official Foundation Display
Topic: Display now upside down after rpi-update [SOLVED]
Replies: 5
Views: 6589

Re: Display now upside down after rip-update

https://www.raspberrypi.org/forums/viewtopic.php?f=43&t=120642#p815820 The screen was the wrong way up originally. It's now the right way round, but you can turn it around. Thank you. It is correct now after adding lcd_rotate=2 to /boot/config.txt, but am I right in thinking that I'm now using the ...
by andy33
Sun Sep 20, 2015 8:11 pm
Forum: Official Foundation Display
Topic: Display now upside down after rpi-update [SOLVED]
Replies: 5
Views: 6589

Display now upside down after rpi-update [SOLVED]

I have just done an rpi-update after reading somewhere that I should to it. Now my display is upside down. Does anyone know how to revert this to the correct orientation?
by andy33
Wed Nov 12, 2014 1:37 pm
Forum: Compute Module
Topic: usbboot - failed to flash image (SOLVED)
Replies: 31
Views: 5847

Re: usbboot - failed to flash image

Gordon, the last and only time I flashed my compute module was on june 26th.That was from a model B and it took 9 minutes but I don't know if the the pi was overclocked. This time it took about 15 mins on a B+ with no overclock. Also I suppose the september img file is larger than the one I used in ...
by andy33
Wed Nov 12, 2014 1:14 pm
Forum: Compute Module
Topic: usbboot - failed to flash image (SOLVED)
Replies: 31
Views: 5847

Re: usbboot - failed to flash image

I checked in a fix to this yesterday evening $ git checkout master $ git pull $ make clean $ make $ sudo make install $ sudo rpiboot Please try again... Thanks Gordon Thank you Gordon, I can confirm that the above worked for me. I have just flashed my compute module and also a blank micro sd card i...
by andy33
Tue Nov 11, 2014 11:58 am
Forum: Compute Module
Topic: usbboot - failed to flash image (SOLVED)
Replies: 31
Views: 5847

Re: usbboot - failed to flash image

gsh wrote:Or try

git checkout 2324612

Gordon
I found that I had to use git checkout -b 2324612 to get it to change but it made no difference, it still will not mount.

Andrew
by andy33
Tue Nov 11, 2014 12:42 am
Forum: Compute Module
Topic: usbboot - failed to flash image (SOLVED)
Replies: 31
Views: 5847

Re: usbboot - failed to flash image

You could try updating from an older version of the usbboot code... git checkout 2324612605316a64f9daae33712e5afe762cf995 should get you to the last known (definitely without doubt) good Gordon I have also had the same problems. I've not flashed my cm for a few months now but I tried today with a f...
by andy33
Wed Jul 23, 2014 11:29 am
Forum: Compute Module
Topic: STICKY: Compute Module Dev Kit Camera IO Adapters - README
Replies: 21
Views: 26951

Re: Compute Module IO Camera Adapters - DO NOT USE

Are there other that havent received a email from farnell yet? I ordered from Farnell netherlands, with a private non business account, but haven;t had any mail or a replacement PCB. Yeah I also ordered fron Farnell netherlands the same way as you. I also still haven't received an email yet. I have...
by andy33
Tue Jul 01, 2014 3:03 pm
Forum: Compute Module
Topic: STICKY: Compute Module Dev Kit Camera IO Adapters - README
Replies: 21
Views: 26951

Re: Compute Module IO Camera Adapters - DO NOT USE

MarkDaniels wrote:Farnell have just sent me an email about this problem, so it looks like they are on the case.
And what is there advice please ? I ordered mine from Farnell but no email yet.
by andy33
Fri Jun 27, 2014 12:29 pm
Forum: Compute Module
Topic: STICKY: Compute Module Dev Kit Camera IO Adapters - README
Replies: 21
Views: 26951

Re: Compute Module IO Camera Adapters - DO NOT USE

I had already tried the camera with a CM module yesterday and it never worked. Today I tried that camera on a raspberry pi and it will not work at all. So it looks like by connecting my camera to the I/O board I have fried my camera :(
by andy33
Thu Jun 26, 2014 10:24 pm
Forum: Compute Module
Topic: It's here, it's real, it works
Replies: 15
Views: 2902

Re: It's here, it's real, it works

Mine took 9 mins to flash from a raspberry pi. It often takes longer than this to write an image to an sd card on my macbook pro!
by andy33
Thu Jun 26, 2014 7:25 pm
Forum: Compute Module
Topic: Rpi Camera
Replies: 13
Views: 2914

Re: Rpi Camera

gsh wrote:I'd suggest for the moment not plugging in the camera to the board, we need to look into the software again and will get back to you...

Gordon
Ok thank you.
by andy33
Thu Jun 26, 2014 7:11 pm
Forum: Compute Module
Topic: Rpi Camera
Replies: 13
Views: 2914

Re: Rpi Camera

When I plug a camera with adapter into either cam0 or cam1 my cm will not even boot and if I disconnect the camera from the I/O board with the power still on it will boot. I followed the instructions from here http://www.raspberrypi.org/documentatio ... -camera.md
by andy33
Thu Feb 27, 2014 10:53 pm
Forum: HATs and other add-ons
Topic: AVRDUDE complains
Replies: 12
Views: 4844

Re: AVRDUDE complains

How are you uploading your sketch?

You need to use Upload Using Programmer from the file menu.
by andy33
Fri Nov 29, 2013 4:46 pm
Forum: HATs and other add-ons
Topic: ATmega setup, etc.
Replies: 39
Views: 11983

Re: ATmega setup, etc.

I've got mine all working fine now after installing wringPi. It wakes up after the set time. But when I start x and run the ide and look at the list of boards it shows Gertuino ATmega44(GPIO). Is this a typo? Should it not read Gertduino ATmega44(GPIO) ?

Andrew
by andy33
Fri Nov 29, 2013 1:27 pm
Forum: HATs and other add-ons
Topic: ATmega setup, etc.
Replies: 39
Views: 11983

Re: ATmega setup, etc.

Yes success :D I did the sensible thing and installed wiringPi and now it works.

Thanks guys.

Andrew
by andy33
Fri Nov 29, 2013 1:11 pm
Forum: HATs and other add-ons
Topic: ATmega setup, etc.
Replies: 39
Views: 11983

Re: ATmega setup, etc.

Thanks Gordon I have got past that bit now by loading the modules on boot. The next problem I get is when I run make in the gdset folder. This time I get this. pi@raspberrypi ~/gertduino/gdset $ make [Compile] gdset.c gdset.c:45:25: fatal error: wiringPiI2C.h: No such file or directory compilation t...
by andy33
Fri Nov 29, 2013 12:31 pm
Forum: HATs and other add-ons
Topic: ATmega setup, etc.
Replies: 39
Views: 11983

Re: ATmega setup, etc.

Hi Gordon, I've got your code onto the 48 but when I run ./setupI get this. pi@raspberrypi ~/gertduino $ ./setup Settup the Pi for DS1374 ./setup: line 5: gpio: command not found /bin/bash: /sys/class/i2c-adapter/i2c-1/new_device: No such file or directory hwclock: Cannot access the Hardware Clock v...
by andy33
Thu Nov 28, 2013 8:07 pm
Forum: HATs and other add-ons
Topic: RPi Reboots instead of Halting
Replies: 19
Views: 6189

Re: RPi Reboots instead of Halting

So i've got the zip file and unzipped it. I now have a folder called gertduino and within that 4 more folders, a txt file and 4 more files. How do I compile and upload a program? I believe it's something to do with the makefile but I have no idea how to use it.
by andy33
Thu Nov 28, 2013 6:59 pm
Forum: HATs and other add-ons
Topic: RPi Reboots instead of Halting
Replies: 19
Views: 6189

Re: RPi Reboots instead of Halting

So do you upload to the 48 via the command line ? Do I use ./program_48 <hex file> ?
by andy33
Thu Nov 28, 2013 5:42 pm
Forum: HATs and other add-ons
Topic: RPi Reboots instead of Halting
Replies: 19
Views: 6189

Re: RPi Reboots instead of Halting

So how do I upload to the 48? I can upload to the 328 no problem using the arduino ide but I have no idea about the 48. In my manual it say's " Use ./program_48 <hex file> to program the device. " Do I need to replace <hex file>>

Thanks,

Andrew
by andy33
Thu Nov 28, 2013 3:07 pm
Forum: HATs and other add-ons
Topic: RPi Reboots instead of Halting
Replies: 19
Views: 6189

Re: RPi Reboots instead of Halting

My Pi also reboots if I use sudo halt but if I put a jumper on the Re pins for the 48 sudo halt halt's. Maybe I need to reset or write something to the 48, but I don't know how to do that yet. I am eagerly waiting for Gordons post. ;)
by andy33
Sat Jun 01, 2013 11:10 am
Forum: Other projects
Topic: Photography Projects
Replies: 150
Views: 66039

Re: Photography Projects

Thanks Texy, I tried the method described in the link but I didn't have much success. I then found this script https://github.com/gonzalo/gphoto2-updater Although I didn't run it as a script. I just ran the commands individually as I was pushed for time. I now have the latest version of gphoto2 on m...
by andy33
Tue May 28, 2013 8:51 pm
Forum: Other projects
Topic: Photography Projects
Replies: 150
Views: 66039

Re: Photography Projects

So does the latest version of gphoto2 2.5.2 fix the usb issue? If so could someone please explain how to compile it on the pi.

Thanks in advance.

Andrew.

Go to advanced search