Raspberry Pi Forums

angel6700

Thank you both, Andreas and pepedog!!

It is really fixed.

Regards.

angel6700

Hello, I have made a case with wood lolly sticks for the raspberry pi. There is a lot of hand work here, but it fits very well. Just a new idea for a case ;) http://dl.dropbox.com/u/40901035/pi/02022013492.jpg http://dl.dropbox.com/u/40901035/pi/02022013493.jpg http://dl.dropbox.com/u/40901035/pi/02...

angel6700

Hello,

I do not know if you have already solved it, but try:

Code: Select all

sudo modprobe i2c-dev
sudo modprobe i2c-bcm2708

I hope this helps.

regards.

angel6700

Hello, Thank you all for your help. I have tried with serial link as explained by Joan, and... ok, I see that I must learn a little of C... Every try with minicom, or pyserial, send just nothing, but using the code provided by Joan: http://www.raspberrypi.org/phpBB3/viewtopic.php?p=252739#p252739 I ...

angel6700

Hello, after reading the article in the last "ThemagPi" magazine about sending a signal with a RF transmitter to a socket and switch it on or off, I found it very interesting. They are the same as these: http://www.ebay.com/itm/1pcs-433Mhz-RF-transmitter-and-receiver-kit-for-Arduino-project-/2610411...

angel6700

Hello,

thanks a lot for the information. Sometimes, when you start something new, it is difficult to know the most basic information. Is for that reason that asking in the correct place can be the best choice.

So, I must start learning the next steps !!

Thank you again.

angel6700

Hello, just a simple question: If I try to do some circuits to work with the gpio pins in the raspberrypi, I know I must be carefull with voltages and currents. So One solution is to use a different power supply for the external circuit, that can be safely isolated by transistors, for example. But, ...

angel6700

Hello,

I can say that (at least for me), removing these kernel parameters from cmdline.txt, it boots even after the pacman -Syu:
init=/bin/systemd
sdhci-bcm2708.cycle_delay=1000

angel6700

I had the same problem after upgrade, and after verifying my raspbian booted with the new firmware, I started trying removing things from cmdline.txt If you remove sdhci-bcm2708.cycle_delay=1000 from cmdline.txt this made my system boot normally. I am not sure what that parameter does, but the new ...

angel6700

Thank you, I will try and post the results later. I recently made a pacman -Rcc... I only hope it was not so recently... And yes, I always do a sync before reboot. BTW, why are only me having this problem?, we all have the same hardware. Or can be just the make-model of SD card. Samsung class 10 8GB...

angel6700

Thank you spenning,
but wher can I find the correct version?
In raspberry pi github there is only the last one (from today, but does not work (for me).

regards,

angel6700

Hello, a couple of days ago, after an update that included firmware using pacman, my pi does not boot. I get this error after 2 secons of power on: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown block(0,0) I have checked the partitin and it is ok. The root parameter in cmdline.t...

angel6700

Hello,

With the new image, I'm not able to run midori. It just open, shows the google home page, and then close.
If I run from console, it say segmentation fault.

Does someone have an idea of this? I'm using netsurf, but is not as capable as midori for certain sites.

Thanks a lot.

.

angel6700

Hello,
trying the new image... but... I think the username/password are no more the same as before.

Which user is defined or which is the root password?

Thank you.

Best regards, and thanks for the Hard work

Edit: Forget this. I rebooted and then it worked as expected.

angel6700

I'm happy you liked it.

Now it looks a bit nicer after modifying that black tape and remaking it with more care.

Regards.

angel6700

Hello, Probably this is not the correct place for this, because the "add-on" I'm going to show you is very simple, but I couldn't find a better place for it. The point that was having problems connecting devices to the usb ports of the raspberry pi, but not with the amount of current the pi can prov...

angel6700

Hello again, I checked the cables and both, hard disk and TV have ground in their AC in cable plug. The only one without it is the power supply for the Pi itself. So I can try to put a wire from the Pi ground pin to the house ground, as you explained. Or I can connect everything to the Pi, switch on...

angel6700

Hello, thanks a lot for the information, very interesting for me. just a question. how can I ground all devices, as you say? The power adaptor for the hard disk has ground and it is connected to the earth terminal in the wall plug. Same for TV. only the power supply for the raspberry pi does not hav...

angel6700

Hello, My Raspberry pi is connected to a TV with HDMI and I only have connected a USB wireless adaptor for my keyboard & mouse. Everything works fine. I have a external hard disk with 3.5 size, so it is powered. I've seen that if I touch shielding of the raspberry usb connector with the usb cable of...

angel6700

Hello,

I have used this one several times and it works very well:
http://www.pyinstaller.org/

You do not need to install, check the docs:
http://www.pyinstaller.org/export/d3398 ... ng-started

good lulck.

angel6700

forumisto wrote:I can't see the photos :/

Sorry, I've just checked and photos are still there.
They are in my dropbox public folder, so can be a problem for you accessing them.

Regards.

angel6700

Hello guys, thanks a lot for your comments. I just need to point that the grid is (of course) non conductive. It is a spare plastic mosquito net for windows (not microsoft windows :lol: ) The board do not stay at the bottom of the case. I will share the sketchup design, where you can see it. I'm gla...

angel6700

Hello, I have made a wood case for my raspberry pi, using a wooden case I bought for 1€. I used Scketch Up for drawing the model using the raspberrypi model I posted some weeks ago. With that I made the holes and ports needed and finally the raspberry logo on top. It has some venting down and up. Th...

angel6700

Hello, I have made a SketchUp model of the raspberry pi, I hope people find it useful. The one reported in the wiki, if more nice but it is true that has some errors in dimenssions. You can download from here: http://db.tt/nW69HGlX http://dl.dropbox.com/u/40901035/RaspberryPi_2.png Regards. Angel.

angel6700

Joe Schmoe wrote:
I just have one question, though. What is "copy"? Did you mean "cp"?

Sorry, it's my error. Of course i mean cp.

Thanks for notifying that. I can not edit my post..

Search found 27 matches

Re: Midori & uzbl both crash Xorg randomly

Lolly sticks case

Re: I2C support for Arch Linux

Re: RF receiver 433MHZ

RF receiver 433MHZ

Re: Begginer question. GPIO circuits.

Begginer question. GPIO circuits.

Re: kernel panic on boot

Re: kernel panic on boot

Re: kernel panic on boot

Re: kernel panic on boot

kernel panic on boot

Midori Segmentation fault

Re: Archlinuxarm v6 hard float

Re: 90 degrees USB

90 degrees USB

Re: HDMI image goes dark when connecting USB

Re: HDMI image goes dark when connecting USB

HDMI image goes dark when connecting USB

Re: Compile python script to binary

Re: My wooden case

Re: My wooden case

My wooden case

New Sketchup model

Re: Copy content of image to sd card instead of whole image