Go to advanced search

by mickey1940
Sat Jun 22, 2019 7:47 pm
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Re: Networking and SSH problems

/etc/resolv.conf is locked into namserver 127.0.0.1 and I need it to say nameserver 192.168.0.1 (Router) so I can get Pi onto Internet. /sbin/resolvconf is what is changing /etc/resolv.conf that is putting nameserver 127.0.0.1 in. How can I stop /sbin/resolconf from changing nameserver in /etc/resol...
by mickey1940
Sat Jun 22, 2019 3:57 pm
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Re: Networking and SSH problems

I already have setup a new password for the Raspi but I did not change Username pi .
by mickey1940
Sat Jun 22, 2019 2:46 pm
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Re: Networking and SSH problems

The command cd , is it not a good command in Debian ?
everytime I use the command sudo cd /root , It comes back with sudo: cd: command not found
What is the problem here ?
by mickey1940
Sat Jun 22, 2019 2:26 pm
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Re: Networking and SSH problems

I deleted everything in /root/.ssh/known_hosts and ran ssh pi@192.168.0.100 and now I'm connected to ssh Raspi. Thanks very much guys. NOW!!! , if you can help me get Raspi connected to the Internet. See my previous message on Network Problems I have a Fedora- Raspi setup to run Rak-Gateway Router 1...
by mickey1940
Sat Jun 22, 2019 1:58 pm
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Re: Networking and SSH problems

This is the file you are talking about. When I open the file , the top line was 192.168.0.102 An I changed it to 192.168.0.3 is this right ? Fedora is 192.168.0.103 Raspi is 192.168.0.100 Router is 192.168.0.1 192.168.0.103 ecdsa-sha2-nistp256 AAAAE2VjZHNhLXNoYTItbmlzdHAyNTYAAAAIbmlzdHAyNTYAAABBBII0...
by mickey1940
Sat Jun 22, 2019 11:55 am
Forum: General discussion
Topic: Networking and SSH problems
Replies: 10
Views: 1033

Networking and SSH problems

I have a Fedora- Raspi setup to run Rak-Gateway Router 192.168.0.1 Fedora 192.168,0,103 Raspi 192.168.0.100 POE (Power Over Ethernet) to power Raspi-Rak gateway. I'm not well up to date on how to make changes in a Debian computer so please take that into consideration. I'm mainly a RPM Guy. On Netwo...
by mickey1940
Mon Jun 17, 2019 4:43 pm
Forum: General discussion
Topic: Getting Raspi , Rak-gateway onto Internet
Replies: 1
Views: 102

Getting Raspi , Rak-gateway onto Internet

Ifconfig shows; Eth0 192.168.10.10 lo 127.0.0.1 wlan0 192.168.12.1 Hookup of Ethernet cable, but I can't ping anything on Internet, but I can ping 192.168.10.10 and 192.168.12.1 Why didn't nmap get installed on Raspi, I can't apt-get install nmap. Raspi can't ping Router at 192.168.0.1 , I can ping ...
by mickey1940
Sun Jun 16, 2019 8:28 pm
Forum: General discussion
Topic: SSH problems
Replies: 1
Views: 159

SSH problems

I have installed Rasp-pi on my Rasperry-Pi and then installed RAK-Gateway. Ip-Address 192.168.10.10 Hostname in /etc/hostname: rak-gateway Before installing rak-gateway I could ssh -l pi 192.168.10.10 connect from my PC to Rasp-Pi If I run : [root@localhost mickey]# ssh -vvv rak-gateway 192.168.10.1...
by mickey1940
Mon Jan 04, 2016 6:54 pm
Forum: General discussion
Topic: Noobs won't work with Display
Replies: 2
Views: 283

Re: Noobs won't work with Display

I also got Ubuntu Mate display working with the above settings.
by mickey1940
Sun Jan 03, 2016 9:48 pm
Forum: General discussion
Topic: Noobs won't work with Display
Replies: 2
Views: 283

Noobs won't work with Display

When using Noobs I can not get the Display to operate. I'm using a HDMI to VGA adapter on Raspberry Pi 2 If I install Raspbian-Jessie and make the following modification to /boot/config.txt : hdmi_force_hotplug=1 hdmi_group=2 hdmi_mode=16 hdmi_drive=2 I can get the Display to work fine I do not use ...

Go to advanced search