Go to advanced search

by BobKruse
Fri Mar 30, 2018 1:58 pm
Forum: Advanced users
Topic: Full schematic for the Pi3 and Zero
Replies: 43
Views: 38323

Re: Full schematic for the Pi3 and Zero

Hello, The official answer about the LAN7515 chip from Microchip came this morning: "Hello, I have received a message from the Business Unit: “This part was a specialized part for Raspberry Pi, so the information is not publicly available. For more information, they would need to go through the Sale...
by BobKruse
Thu Mar 15, 2018 3:19 pm
Forum: Advanced users
Topic: Full schematic for the Pi3 and Zero
Replies: 43
Views: 38323

Re: Full schematic for the Pi3 and Zero

I posted a request for LAN7515 documentation yesterday on the Microchip web site, with no response so far.
Maybe it's just a new part.
The ECIA shows no authorized distributors for the LAN7515. 10 distributors for the LAN7500.
https://www.eciaauthorized.com/en/search/LAN7515
by BobKruse
Wed Mar 14, 2018 5:44 pm
Forum: Advanced users
Topic: Full schematic for the Pi3 and Zero
Replies: 43
Views: 38323

Re: Full schematic for the Pi3 and Zero

Hi, We're designing a board that uses a couple CM3 modules. And we are right at the stage of putting in the USB to Ethernet bridge. It happens to be PI day, and you upgraded the Ethernet to a LAN7515. You published the schematic for the IO board, and I appreciate it. I was hoping to look up the appr...
by BobKruse
Tue Feb 07, 2017 8:44 pm
Forum: Troubleshooting
Topic: STICKY:I2C, SPI, I2S, LIRC, PPS, stopped working? Read this.
Replies: 335
Views: 531236

Re: I2C, SPI, I2S, LIRC, PPS, stopped working? Read this.

DougieLawson & SunDontShine, Am I wrong, or stating the obvious? I think the error message "gpio: Unable to load/unload modules as this Pi has the device tree enabled. You need to run the raspi-config program (as root) and select the modules (SPI or I2C) that you wish to load/unload there and reboot...
by BobKruse
Fri Mar 25, 2016 12:43 pm
Forum: Java
Topic: Oracle license fees for Java on Raspberry Pi are cheap
Replies: 34
Views: 15504

Re: Oracle license fees for Java on Raspberry Pi are cheap

Hello, I apologize for extending a 2 year old thread, but it's missing the corner case that applies to my project. With any luck Henrik, or some other Oracle expert is still monitoring the thread. We design, manufacture and sell embedded industrial controllers, soon to be based on the Pi, and probab...
by BobKruse
Thu Dec 17, 2015 9:25 pm
Forum: Raspbian
Topic: Why is Jessie asking for a password?
Replies: 29
Views: 16763

Re: Why is Jessie asking for a password?

Hi I ran into this this morning. I was hoping that the Jessie lite image would have the gui desktop, but not all the office/games/sound/educational toys. Instead it had a stripped cli for the headless folks. When I tried to enable boot to gui in raspi-config it suggested that it apt-get install ligh...
by BobKruse
Tue Dec 15, 2015 9:09 pm
Forum: Raspbian
Topic: attach i2c addr & gpio input pin to ar1021_i2c driver
Replies: 1
Views: 1186

Re: attach i2c addr & gpio input pin to ar1021_i2c driver

~/linux/arch/arm/boot/dts/bcm2709-rpi-2-b.dts now contains a section: &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; clock-frequency = <100000>; ar1021_i2c@4d { compatible = "microchip,ar1021-i2c"; reg = <0x4d>; interrupt-parent = <&gpio>; interrupts = <23 0x8>; gpios = <&gpio 23 2>; }...
by BobKruse
Sun Nov 29, 2015 3:49 am
Forum: Troubleshooting
Topic: STICKY:I2C, SPI, I2S, LIRC, PPS, stopped working? Read this.
Replies: 335
Views: 531236

Re: I2C, SPI, I2S, LIRC, PPS, stopped working? Read this.

Hello Reidmere, I'm not familiar with the device you are interfacing to your PI. You mentioned that it uses a 16Mhz clock. I don't think the Broadcom 2835/36 supports any I2C clock speeds other than 100KHz and 400KHz. See the peripherals manual http://www.farnell.com/datasheets/1521578.pdf. 16Mhz se...
by BobKruse
Sat Oct 31, 2015 1:56 am
Forum: Raspbian
Topic: attach i2c addr & gpio input pin to ar1021_i2c driver
Replies: 1
Views: 1186

attach i2c addr & gpio input pin to ar1021_i2c driver

Hi, I'm testing a carrier board that I designed for the Raspberry Pi 2. (okay, okay, I just pasted in some example circuits so the assembly will do what I need it to.) Along with some other stuff, I have a rtc circuit and a touchscreen circuit connected to the i2c bus. The i2c bus is working because...
by BobKruse
Thu May 21, 2015 6:41 pm
Forum: Compute Module
Topic: Raspberry Pi Compute Module Reformat
Replies: 2
Views: 1007

Re: Raspberry Pi Compute Module Reformat

Hello, I just received my compute module this week I've spent a full day trying to get the latest Raspbian image to boot up. I got 2015-02-16-raspbian-wheezy.zip from https://www.raspberrypi.org/downloads/, followed directions and copied it over from my rpi2. No luck. I found this link https://www.r...

Go to advanced search