Hello, I try to Monitor Network speed with RPI-Monitor and Iperf, but I get this error: Warning: unable to close filehandle FEED properly. RPI-Monitor Release is 2.12-r0 This is my iperf.conf file: dynamic.17.name=Iperf dynamic.17.source=iperf -p 4711 -c 192.168.0.254 | grep -Po '(?<=,)[0-9]+$|[0-9....
maybe is there a software with input Rpi-Cam and output 2 virtual video device or raspivid record a file and pipe the frames forward to motion?
Motion can pipe the raw Video to stdin, can raspivid record from stdin?
i have the same Problem, i install Rasbian and Motion and all working.
After unplug and move the RPI to the right place i get this error.
Raspistill has given me the right tip, i have only 32 MB gpu splittmemory.
After change to 128 MB Motion work.
Hello, i setup a Raspberry Pi B2 with a WiFi dongel with rtl8192cu chip. The Dongel connect to my Accesspoint show SNR(db) 43 and CCQ(%) 100, but the Datarate show between 1 - 2 Mbps. I try 2 dongels a Edimax and a dongel that show my 0bda:8178 in the lsusb. Wenn i switch to a TP-Link TL-WN722N the ...
Hallo, Mein Raspberry with Rasbian connects always to update pages. Is this normal and necessary? Here are a few log entries: GET /debian/dists/wheezy/Release.gpg HTTP/1.1 Host: archive.raspberrypi.org GET /debian/dists/wheezy/Release HTTP/1.1 Host: archive.raspberrypi.org GET /debian/dists/wheezy/m...
i serach for a Server to run on the Raspberry that provide a search index for all files in my network.
Like the windows serarch index including file contents.
is there something like this?
I have found the problem.
Jackd shows after starting an output and does not release the console.
Now i start jackd with nohub and "2>/dev/null &" at the end.
Hello, i use a recording system with Rotter. all attempts start Rotter after booting automatically failed. Rotter use the jackd, which I start in the rc.local. From the commandline i can start rotter with: rotter -q -a -f flac -c 1 -d 250 -q -L flat /home/pi/archives & disown Where can i put this li...
Hello, i would like stream the RPi No IR Camera with rtsp, I have no problem with the stream, but i cant switch to -ex night. I use this command: raspivid -ex night -n -w 1280 -h 720 -b 4500000 -fps 30 -vf -hf -t 0 -o - | cvlc -vvv stream:///dev/stdin --sout '#rtp{sdp=rtsp://:8554/}' :demux=h264 if ...
The Pi is in range, but difficulties accessing, but I need to make it.
Here I have found the error.
I have an Error in the fstab, after i try to mount a extern Folder.
In case anybody else comes across this thread as a result of searching for the title, adding an "ro" parameter to /boot/cmdline.txt fixed it for me and allowed my system to fsck correctly. Hello, where must the "ro" is entered? This is my cmdline.txt: dwc_otg.lpm_enable=0 console=ttyAMA0,115200 con...
my problem is, i cut off the power supply and the Pi reboot.
But SSH still not working.
"ssh: connect to host 192.168.0.112 port 22: Connection refused"
Hello, after a reboot my Rpi do not accept a ssh connection. For a Test i try the Rpi-monitor, the startpage is viewing, but rpi can't access the json datei. The Pi is unfortunately far away, is there a way to revive him again? The voltage I have already switched off and on, without success. regards...
where you write the Motion files, on an exern shared folder over WiFi?
My Edimax connection was still poor and i change to Netis 300 Mbps Wireless N USB adapter with dual antenna.
Look at you Wifi Signal "sudo ifconfig wlan0 up" or "watch -n 1 cat /proc/net/wireless"
Hello, i use the Raspberry with the Camera board. It all looks good, but in the log is this error: [1] [INF] [ENC] [Oct 03 09:19:53] ffmpeg_avcodec_log: err{or,}_recognition separate: 1; 1 - flag 48 [1] [INF] [ENC] [Oct 03 09:19:53] ffmpeg_avcodec_log: err{or,}_recognition combined: 1; 1 - flag 48 [...